PROVERTHA launches new MVB/WTB bus connectors to meet the high demands of railway technology
360° shielding and torsion- and vibration-proof field connection with MVB/WTB cables
Pforzheim – 15 February 2021 – Provertha has developed new D-Sub bus connectors specifically designed for communication in the two bus systems MVB (Multifunction Vehicle Bus) and WTB (Wired Train Bus) of the Train Communication Network (TCN). The new connector types enable reliable, vibration-proof connection of MVB/WTB cables to the MVB and WTB interfaces. During the development of the new connectors, the high requirements of railway technology, above all vibration safety, were taken into account. This is why Provertha has equipped the connectors with a vibration-proof screw-type locking system at the MVB or WTB interface. The combination of the vibration-proof single-wire connection and the vibration-proof connection of the shielding and strain relief results in maximum functional and operational safety in the railway sector.

Bus connectors enable T-bus wiring and bus termination

TCN is a hierarchically structured system for MVB or WTB and was developed specifically for railway vehicles to replace analogue remote control and to record the operating states of the individual vehicles. The MVB is a field bus used for data communication within a rail vehicle, whereas the WTB spans several vehicles – it ensures communication between individual rail vehicles.

The new bus connectors allow bus wiring with T-functionality. This means that the bus connections remain intact even if the connector is disconnected from the interface module or a module fails. There are terminating resistors and measuring capacitors on the bus circuit board which are activated by solder bridges. Special PCB solutions with individual functions can be realised.

RF-shielded housing design with axial outputs for vibration-proof connection

The D-Sub bus connectors have two axial cable outlets next to each other, i.e. arranged at 180° to the mating direction – ideal for interfaces directly above each other. The special RF-shielded design of the zinc die-cast housing with overlapping outer contours, together with the adapted crimp flange/sleeve combination, ensures 360° shielding, with the crimped connection providing torsion- and vibration-proof strain relief and optimum shield contact over the entire service life. The hexagonal crimp of the sleeve also ensures a reliable gas-tight connection of the cable shield.

To ensure vibration safety, the individual wires are connected with cage clamp terminals. The screw-type locking of the bus connector at the MVB or WTB interface is also designed to be vibration-proof thanks to the hexagon socket screw with spring washer underneath – optionally with a UNC 4-40 or M3 thread.

Complete sets and customised variants

The D-Sub connectors with IP 30 protection are available as either pins or sockets and can be used in a temperature range from -20 °C to +70 °C. They are designed for a mechanical life of 500 (PL1 according to CECC 75301-802) and 250 mating cycles (PL2 according to CECC 75301-802). For the various MVB and WTB cable connections, they are available as a complete set including the respective crimp flange/sleeve combination. Customised versions are also available on request, in which case – depending on the required cable type – a validated flange-sleeve combination is also supplied. Furthermore, special PCB solutions according to customer specifications are also possible.

About PROVERTHA

PROVERTHA Connectors, Cables & Solutions GmbH, a privately-owned business founded in Pforzheim, Germany, in 1981, has more than 800 employees at four locations in Germany and Hungary. Among the many customers from 45 countries are companies from the automotive, aerospace, healthcare, and electronics markets. A tight network of distribution partners ensures customer proximity and competent technical service.

PROVERTHA’s large range of products and services include standard and special connectors with an extensive range of accessories, including data cables, harnesses and cable looms as well as complete solutions for plastic moulding and tool making. By means of an online order service, even small order quantities from the comprehensive product catalogue can be delivered on time. A QS9000, DINISO 9001 and IATF 16949 certified quality management together with a UL certified cable assembly guarantee high product quality. The ISO 14001 certification of our manufacturing sites ensures the environmentally friendly manufacturing of our products.
 
 
 
» Provertha
» Press Releases
» Press Release
Date: 15.02.2021 16:30
Number: I_01-20212_MVB-WTB_Busstecker_EN
» Press Photos

 Download der hochauflösenden Version...
D-Sub connector for MVB/WTB fieldbus cables in rail vehicles
» Contacts
PROVERTHA Connectors, Cables & Solutions GmbH
Westring 9
75180 Pforzheim (Germany)
Manfred Schock
Tel. +49 (0)7231 774-23
Fax: +49 (0)7231 774-44
manfred.schock@provertha.com
www.provertha.com
» Contact Agency
MEXPERTS AG
Wildmoos 7
D-82266 Inning am Ammersee
Matthias May
Tel. +49 (0)8143 59744-16
matthias.may@mexperts.de
www.mexperts.de
» More Press Releases
06.11.2024 10:00
Smallest PCB footprint and highly reliable: Angled M12 SMT Ruggedized connectors from PROVERTHA

24.10.2024 12:00
PROVERTHA offers new SMT Slimline circular connectors in M12 format with standard footprint

15.10.2024 10:00
Compact and secure for high mechanical requirements: M12 SMT Ruggedized connectors from PROVERTHA

20.03.2024 11:00
PROVERTHA has developed a new compact wire-to-board solution for sensor tubes with a diameter of 9 mm

12.02.2024 09:30
PROVERTHA offers compact M12 Ethernet adapter as panel feed-through solution for connecting railway CCTV surveillance cameras